TOOL GUIDE
Duct fabrication & material take-off
Calculate duct material quantities and mass from editable example values or your own inputs.
Purpose & scope
Calculate duct material quantities and mass from editable example values or your own inputs.
The integral-flange sample adds 30 mm/end and no separate flange mass. Sample section length is capped at 1.14 m for a 1.22 m sheet dimension with 20 mm cutting reserve. This is an operating example; use actual machine development and sheet dimensions. Quick joint/stiffener choices do not verify pressure capacity.
Inputs
Use drawings, design conditions and manufacturer data. Units and example values follow the calculator; example values are not universal design requirements.
| Parameter | Value / interpretation |
|---|---|
| Duct shape | Select the actual geometry, material or construction. |
| Sheet material | Select the actual geometry, material or construction. |
| Outside width / outside diameter · mm | Allowed input range: 50–5000 mm. Example values are not prescribed construction or capacities. |
| Outside height · mm | Allowed input range: 50–5000 mm. Example values are not prescribed construction or capacities. |
| Thickness selection | Select the actual geometry, material or construction. |
| Sheet thickness · mm | Allowed input range: 0.3–5 mm. Example values are not prescribed construction or capacities. |
| Straight run length · m | Allowed input range: 0.1–10000 m. Example values are not prescribed construction or capacities. |
| Maximum fabricated section length · m | Allowed input range: 0.1–6 m. Example values are not prescribed construction or capacities. |
| Signed design static pressure · Pa | Allowed input range: -10000–10000 Pa. Example values are not prescribed construction or capacities. |
| Transverse joint selection | Select the actual geometry, material or construction. |
| Quick joint setup | Select the actual geometry, material or construction. |
| Quick stiffener setup | Select the actual geometry, material or construction. |
| Transverse joint | Select the actual geometry, material or construction. |
| Terminal flange frames | Allowed input range: 0–2 . Example values are not prescribed construction or capacities. |
| Flange / coupling mass per perimeter metre · kg/m | Allowed input range: 0–20 kg/m. Example values are not prescribed construction or capacities. |
| Maximum intermediate stiffener spacing · m | Allowed input range: 0.1–6 m. Example values are not prescribed construction or capacities. |
| Stiffener mass per perimeter metre · kg/m | Allowed input range: 0–20 kg/m. Example values are not prescribed construction or capacities. |
| Quick external insulation | Select the actual geometry, material or construction. |
| Sheet allowance per longitudinal seam · mm | Allowed input range: 0–100 mm. Example values are not prescribed construction or capacities. |
| Longitudinal seams per cross-section | Allowed input range: 0–8 . Example values are not prescribed construction or capacities. |
| Sheet allowance at each section end · mm | Allowed input range: 0–100 mm. Example values are not prescribed construction or capacities. |
| Sheet purchasing waste · % | Allowed input range: 0–100 %. Example values are not prescribed construction or capacities. |
| External insulation thickness · mm | Allowed input range: 0–300 mm. Example values are not prescribed construction or capacities. |
| Insulation density · kg/m³ | Allowed input range: 0–500 kg/m³. Example values are not prescribed construction or capacities. |
| Additional distributed mass · kg/m | Allowed input range: 0–500 kg/m. Example values are not prescribed construction or capacities. |
Steps
- Enter outside dimensions, material, thickness and run/section lengths. Inputs have example values to get started.
- Use ? for thickness suggestions and usable section length from sheet size. Choose joint, stiffener and insulation presets to fill their parameters. Open Edit detailed parameters to customize.
- Automatic mode updates thickness and flanges with size within the suggestion scope. Manual edits switch that setting to Manual. Name and save each segment in a project for a combined schedule report/PDF.
- Review quantities before/after waste, transfer installed mass to supports and save the project or export JSON.
Worked example
This reproducible training example uses the values below. Select the appropriate mode and overwrite restored project values. Example rates, K values and equipment losses are assumptions, not mandatory design criteria.
All example inputs
| Parameter | Value / interpretation |
|---|---|
| Duct shape | rect |
| Sheet material | steel |
| Outside width / outside diameter | 600 mm |
| Outside height | 400 mm |
| Thickness selection | auto |
| Sheet thickness | 0.8 mm |
| Straight run length | 12 m |
| Maximum fabricated section length | 1.2 m |
| Signed design static pressure | 500 Pa |
| Transverse joint selection | auto |
| Quick joint setup | angle25 |
| Quick stiffener setup | none |
| Transverse joint | angle |
| Terminal flange frames | 2 |
| Flange / coupling mass per perimeter metre | 1.10685 kg/m |
| Maximum intermediate stiffener spacing | 0.6 m |
| Stiffener mass per perimeter metre | 0 kg/m |
| Quick external insulation | 25-48 |
| Sheet allowance per longitudinal seam | 30 mm |
| Longitudinal seams per cross-section | 2 |
| Sheet allowance at each section end | 0 mm |
| Sheet purchasing waste | 10 % |
| External insulation thickness | 25 mm |
| Insulation density | 48 kg/m³ |
| Additional distributed mass | 0 kg/m |
Expected results (rounded)
| Parameter | Value / interpretation |
|---|---|
| Purchased sheet including waste | 27.15 m² |
| Installed mass | 229.51 kg |
| Internal connections | 9 |
Small differences in displayed rounding are normal. A result that passes the entered limits does not establish suitability for the complete system.
Method & limitations
The integral-flange sample adds 30 mm/end and no separate flange mass. Sample section length is capped at 1.14 m for a 1.22 m sheet dimension with 20 mm cutting reserve. This is an operating example; use actual machine development and sheet dimensions. Quick joint/stiffener choices do not verify pressure capacity.
Automatic mode updates thickness and joints when low-pressure rectangular galvanized duct dimensions change. Manual edits switch that setting to Manual. Combinations are starting values for material quantities, not pressure-capacity checks or mandatory construction.
All inputs start with editable example values. Section length and waste can be adjusted to match the sheet size and fabrication method. Pressure records the design condition and does not enter the take-off equations.
Straight, constant-section duct run only. Dimensions are outside the sheet-metal shell, excluding insulation. Density is the stated example material value; coating mass is not calculated separately.
Sections N = ceil(L/l); internal joints = N−1. Flanges use two frames per joint plus entered terminal frames. Slip joints/bands use one perimeter per joint and exclude terminal frames. Intermediate stiffeners restart in each fabricated section and exclude end frames.
Developed sheet area = mean perimeter × L + seam allowances + end allowances. Purchased sheet includes waste; installed mass excludes waste. For integral flanges, enter the actual end development and set additional flange mass to zero if already included in that sheet development.
Elbows, transitions, tees, access doors, dampers, bolts, corners, gaskets, sealant and nesting optimization are excluded. A joint name alone does not establish sheet/joint strength, leakage class or pressure capacity.
The integral-flange sample adds 30 mm/end and no separate flange mass. Sample section length is capped at 1.14 m for a 1.22 m sheet dimension with 20 mm cutting reserve. This is an operating example; use actual machine development and sheet dimensions. Quick joint/stiffener choices do not verify pressure capacity.
Common mistakes
Mixing outside/clear dimensions; treating example values as required construction; adding purchasing waste to hanger load; double counting integral flange sheet.
Projects & reports
- Choose or create an engineering project and enter your actual design inputs.
- Project inputs/results are autosaved in this browser. Where a saved-list panel is available, name and add the selected section or alternative to compare multiple options.
- Review the report before exporting PDF. In the print dialog select Save as PDF. Export JSON for backup and use Open file to restore it; PDF cannot restore project data.
Saved results do not automatically recalculate when another tool changes. Review any dependency warning, recalculate and update the affected results.
References & related tools
The tool implements the methods and limits stated above; linking a standard does not establish complete compliance with that standard.