TOOL GUIDE
Duct trapeze & hanger rod checks
Select rods and bearers from trial loads, check each trapeze and save run schedules for reporting.
Purpose & scope
Select rods and bearers from trial loads, check each trapeze and save run schedules for reporting.
Example trapeze count = ceil(run length/spacing)+1, including both ends of each independent run. The entered spacing remains the conservative tributary length for checks. Bearer total is the rod-to-rod span only, excluding end extensions; rod totals exclude splices, nuts and embedment. Shared end supports across rows are not merged.
Inputs
Use drawings, design conditions and manufacturer data. Units and example values follow the calculator; example values are not universal design requirements.
| Parameter | Value / interpretation |
|---|---|
| Duct shape | Select the actual geometry, material or construction. |
| Sheet material | Select the actual geometry, material or construction. |
| Outside width / outside diameter · mm | Allowed input range: 50–5000 mm. Example values are not prescribed construction or capacities. |
| Outside height · mm | Allowed input range: 50–5000 mm. Example values are not prescribed construction or capacities. |
| Thickness selection | Select the actual geometry, material or construction. |
| Sheet thickness · mm | Allowed input range: 0.3–5 mm. Example values are not prescribed construction or capacities. |
| Insulation preset | Select the actual geometry, material or construction. |
| External insulation thickness · mm | Allowed input range: 0–300 mm. Example values are not prescribed construction or capacities. |
| Insulation density · kg/m³ | Allowed input range: 0–500 kg/m³. Example values are not prescribed construction or capacities. |
| Additional distributed mass · kg/m | Allowed input range: 0–500 kg/m. Example values are not prescribed construction or capacities. |
| Equivalent joint/stiffener mass · kg/m | Allowed input range: 0–500 kg/m. Example values are not prescribed construction or capacities. |
| Additional point mass on this trapeze · kg | Allowed input range: 0–1000 kg. Example values are not prescribed construction or capacities. |
| Straight run length · m | Allowed input range: 0.1–10000 m. Example values are not prescribed construction or capacities. |
| Rod span selection | Select the actual geometry, material or construction. |
| Longitudinal hanger spacing · m | Allowed input range: 0.1–6 m. Example values are not prescribed construction or capacities. |
| Bearer span between rods · m | Allowed input range: 0.1–6 m. Example values are not prescribed construction or capacities. |
| Metric coarse-thread rod | Select the actual geometry, material or construction. |
| Length of each rod · m | Allowed input range: 0.05–10 m. Example values are not prescribed construction or capacities. |
| Bearer mass per metre · kg/m | Allowed input range: 0–100 kg/m. Example values are not prescribed construction or capacities. |
| Clearance each side of insulated duct · mm | Allowed input range: 0–500 mm. Example values are not prescribed construction or capacities. |
| Rod & bearer selection | Select the actual geometry, material or construction. |
| Support calculation basis | Select the actual geometry, material or construction. |
| Bearer · depth vertical | Select the actual geometry, material or construction. |
| Yield-strength divisor (preliminary assumption) | Allowed input range: 1.5–5 . Example values are not prescribed construction or capacities. |
| Section-property / allowable-value reference | Record the source document and revision for traceability. |
| Rod property class / product reference | Record the source document and revision for traceability. |
| Bearer section & installed orientation | Record the source document and revision for traceability. |
| Allowable rod tensile stress (0: unavailable) · MPa | Allowed input range: 0–1000 MPa. Example values are not prescribed construction or capacities. |
| Bearer section modulus about bending axis (0: unavailable) · cm³ | Allowed input range: 0–1000 cm³. Example values are not prescribed construction or capacities. |
| Bearer second moment about bending axis (0: unavailable) · cm⁴ | Allowed input range: 0–10000 cm⁴. Example values are not prescribed construction or capacities. |
| Bearer elastic modulus · MPa | Allowed input range: 10000–300000 MPa. Example values are not prescribed construction or capacities. |
| Allowable bending stress (0: unavailable) · MPa | Allowed input range: 0–1000 MPa. Example values are not prescribed construction or capacities. |
| Anchor product, substrate & capacity reference | Record the source document and revision for traceability. |
| Allowable tension per anchor (0: unavailable) · kN | Allowed input range: 0–1000 kN. Example values are not prescribed construction or capacities. |
| Deflection limit L / divisor | Allowed input range: 100–1000 . Example values are not prescribed construction or capacities. |
Steps
- Enter outside dimensions for automatic thickness or override it manually, then select insulation. Retain thickness and joint/stiffener loads received from fabrication.
- Enter run length, hanger spacing and rod length. Span follows insulated width plus clearance; edit span for a manual value.
- Automatic mode screens rod/bearer choices against the load and preliminary assumptions. Use verified data for other sections and supply anchor data separately.
- Name and save each run to summarize trapezes and rod/bearer lengths in reports/PDF.
Worked example
This reproducible training example uses the values below. Select the appropriate mode and overwrite restored project values. Example rates, K values and equipment losses are assumptions, not mandatory design criteria.
All example inputs
| Parameter | Value / interpretation |
|---|---|
| Duct shape | rect |
| Sheet material | steel |
| Outside width / outside diameter | 600 mm |
| Outside height | 400 mm |
| Thickness selection | auto |
| Sheet thickness | 0.8 mm |
| Insulation preset | 25-48 |
| External insulation thickness | 25 mm |
| Insulation density | 48 kg/m³ |
| Additional distributed mass | 0 kg/m |
| Equivalent joint/stiffener mass | 2 kg/m |
| Additional point mass on this trapeze | 0 kg |
| Straight run length | 12 m |
| Rod span selection | auto |
| Longitudinal hanger spacing | 2.4 m |
| Bearer span between rods | 0.8 m |
| Metric coarse-thread rod | M8 |
| Length of each rod | 1 m |
| Bearer mass per metre | 2.3864 kg/m |
| Clearance each side of insulated duct | 75 mm |
| Rod & bearer selection | auto |
| Support calculation basis | preliminary |
| Bearer · depth vertical | rhs40 |
| Yield-strength divisor (preliminary assumption) | 3 |
| Section-property / allowable-value reference | |
| Rod property class / product reference | |
| Bearer section & installed orientation | |
| Allowable rod tensile stress (0: unavailable) | 80 MPa |
| Bearer section modulus about bending axis (0: unavailable) | 3.6682666666666663 cm³ |
| Bearer second moment about bending axis (0: unavailable) | 7.336533333333333 cm⁴ |
| Bearer elastic modulus | 200000 MPa |
| Allowable bending stress (0: unavailable) | 78.33333333333333 MPa |
| Anchor product, substrate & capacity reference | |
| Allowable tension per anchor (0: unavailable) | 0 kN |
| Deflection limit L / divisor | 250 |
Expected results (rounded)
| Parameter | Value / interpretation |
|---|---|
| Tension per rod/anchor | 0.21 kN |
| Rod tensile stress | 5.85 MPa |
| Bearer moment | 82.18 N·m |
| Minimum I for example deflection limit | 0.69 cm⁴ |
Small differences in displayed rounding are normal. A result that passes the entered limits does not establish suitability for the complete system.
Method & limitations
Example trapeze count = ceil(run length/spacing)+1, including both ends of each independent run. The entered spacing remains the conservative tributary length for checks. Bearer total is the rod-to-rod span only, excluding end extensions; rod totals exclude splices, nuts and embedment. Shared end supports across rows are not merged.
Automatic selection checks bearer bending/deflection and rod tension independently, trying candidates from small to large. The largest candidate must still be checked; anchors are not selected. Editing a rod/bearer or span switches that setting to Manual.
Automatic selection screens M8–M20 rods and RHS 40×40×2, 60×40×2, 80×40×2 for rod tension, bearer bending and deflection; it does not select anchors. Editing a rod/bearer or span switches that setting to Manual. Verified-data mode never replaces section properties.
Preliminary mode assumes class 4.6 rods (fy=240 MPa) and S235 RHS (fy=235 MPa). The default divisor 3 is a tool screening assumption, not a prescribed design factor under an applicable code. I=(b h³−bi hi³)/12; Z=I/(h/2); self-weight uses section area ×7850 kg/m³. Ideal sharp corners with h vertical; these are not actual product catalogue properties.
Two vertical rods, symmetric loading and a simply supported bearer. Duct load over one hanger spacing is conservatively represented as a centre point load, compared with a symmetric load spread over the duct width. Bearer self-weight is uniform; each rod self-weight adds to anchor tension.
Mmax = P L/4 + Wbearer L/8; centre deflection = P L³/(48 EI) + 5 Wbearer L³/(384 EI). Rod stress = R/As; bearer bending stress = M/Z. As is the metric coarse-thread tensile stress area, not the nominal circular area.
Entered limits must be compatible allowable values for the service-load basis, with suitable safety factors already included. Do not enter ultimate failure loads or unconverted design resistances. Without a reference/capacity value, requirements are shown without a passing verdict.
Angle/channel names alone do not establish capacity: I and Z must match the bending axis and installed orientation. Torsion, instability, perforations, rod–bearer connections, local shell bearing, round-duct saddles, anchor substrate, edge distances, anchor groups and supporting structure are not checked.
Static gravity loads only; seismic, wind, vibration, person loads, risers, cantilevers, fire/smoke-rated ducts and code-required hanger spacing are excluded. Entered spacing is a trial assumption, not a recommended maximum.
Example trapeze count = ceil(run length/spacing)+1, including both ends of each independent run. The entered spacing remains the conservative tributary length for checks. Bearer total is the rod-to-rod span only, excluding end extensions; rod totals exclude splices, nuts and embedment. Shared end supports across rows are not merged.
Common mistakes
Using nominal circular area instead of thread As; wrong I/Z units or axis; ultimate anchor load used as allowable; omitted self-weight/insulation/accessories; treating component checks as complete-system approval.
Projects & reports
- Choose or create an engineering project and enter your actual design inputs.
- Project inputs/results are autosaved in this browser. Where a saved-list panel is available, name and add the selected section or alternative to compare multiple options.
- Review the report before exporting PDF. In the print dialog select Save as PDF. Export JSON for backup and use Open file to restore it; PDF cannot restore project data.
Saved results do not automatically recalculate when another tool changes. Review any dependency warning, recalculate and update the affected results.
References & related tools
The tool implements the methods and limits stated above; linking a standard does not establish complete compliance with that standard.